U-Boot 2015.01-svn9116 (Jan 09 2025 - 16:32:35), Build: jenkins-GSP_ERR241224208-TASK1_release_lianmingzeng_20250102_1XXX-S3H_linux-11
Version: I2g#######
DRAM:
WARNING: Caches not enabled
SPINAND: _MDrv_SPINAND_GET_INFO: Found SPINAND INFO
(0xEF) (0xAA) (0x20)
SPINAND: board_nand_init: CIS contains part info
64 MiB
MMC: MStar SD/MMC: 0
unexpected character ' ' at the end of partition
In: serial
Out: serial
Err: serial
Auto-Negotiation...
Link Status Speed:100 Full-duplex:1
sstar_emac
Hit any key to stop autoboot: 0
SigmaStar # help
? - alias for 'help'
aes - Control Mstar AES engine
autoup - load update file from server
boot - boot default, i.e., run 'bootcmd'
bootlogo- show bootlogo
bootm - boot application image from memory
chpart - change active partition
dbg - set debug message level. Default level is INFO
debug - Disable uart rx via PAD_DDCA to use debug tool
devid - devid - set hardware id and save to flash
do_ECC - Enable or disable internal ecc. #do_ECC 0 (disable), do_ECC (enable)
do_bbm - Swap block (winbond only), #do_bbm LBA PBA
dstar - script via SD/MMC
eeprom - EEPROM sub-system
envbperase- erase env flash region
envbppri- print environment variables
eracfg - eracfg - erase config sectors
eralogo - eralogo - erase logo sectors
estar - script via network
estart - EMAC start
fatread - FAT fatread with FSTART
fb_needreset- get_key - get shift key
fb_set - fb_set - get shift key
fsload - fsload - load binary file from a filesystem image
get_key - get_key - get shift key
gpio - Config gpio port
help - print command description/usage
i2c - I2C sub-system
initDbgLevel- Initial varaible 'dbgLevel'
kaimendaji- - kai men da ji
lock_otp- lock_otp - otp lock
lock_status- lock_status - get otp lock status
mac - mac - set mac address and save to flash
mac1 - mac1 - set mac1 address and save to flash
macaddr - setup EMAC MAC addr
mssdmmc - Mstar SD/MMC IP Verification System
mstar - script via TFTP
mtdparts- define flash/nand partitions
mxp - MXP function for Mstar MXP partition
nand - NAND sub-system
nboot - boot from NAND device
net_upgrade - do net update from the specified file that is in tftpserver
otp_printf- otp_printf - printf otp value
ping - send ICMP ECHO_REQUEST to network host
readbbm - Read BBM table
readcis - Read cis block content
reset - Perform RESET of the CPU
riu - riu - riu command
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
sdstar - script via sd package
secauth - Control Sstar security authenticate sequence
setenv - set environment variables
sfbin - for uploading sf image to a server(via network using TFTP protocol)
show_hello- - hello world
srcfg - sensor pin and mclk configuration.
usbstar - script via USB package
usbupdate- usbupdate - update the system via USB_DISK, without console
ustar - script via USB
version - print monitor, compiler and linker version
writecis- Search CIS in dram then write to spinand.
xhprint - - hello world
xhprintenv- print environment variables
SigmaStar #
SigmaStar # 帮助
? - '帮助'的别名
aes - 控制Mstar A引擎
autoup - 从服务器加载更新文件
boot - 启动默认，即运行'bootcmd'
bootlogo- 显示启动logo
bootm- 从内存启动应用程序映像
chpart - 更改活动分区
dbg - 设置调试消息级别。默认级别是INFO
debug - 用通过PAD_DDCA的uart rx，以使用调试工具
devid - devid - 设置硬件id并保存到flash
doECC - 启用或禁用内部ecc。#do_ECC 0（禁用），do_ECC（启用）
do_bbm 交换块（仅限winbond），#do_bbm LBA PBA
dstar - 通过SD/MMC运行脚本
eeprom EEPROM子系统
envbperase- 擦除env闪存区域
envbppri- 打印环境变量
eracfg - erac - 擦除配置扇区哈哈
eralogo - eralogo - 擦除logo扇区
estar - 通过网络运行脚本
estart -AC启动
fatread - FAT fatread 使用FSTART
fb_needreset- get_key - 获取shift键
fb_set - fb_ - 获取shift键
fsload - fsload - 从文件系统映像加载二进制文件
get_key - get_key - shift键
gpio - 配置gpio端口
help - 打印命令描述/用法
i2c - I2C子系统
initDLevel- 初始化变量'dbgLevel'
kaimendaji- - 开明大计
lock_otp- lock_otp - otp锁定
lock_status- lock_status - 获取otp锁定状态
mac - mac - 设置mac地址并保存到flash
mac1 - mac - 设置mac1地址并保存到flash
macaddr - 设置EMAC MAC地址
mssdmmc - Mstar SD/MMC IP验证
mstar - 通过TFTP运行脚本
mtdparts- 定义闪存/nand分区
mxp - Mstar MXP分区的MX功能
nand - NAND子系统
nboot - 从NAND设备启动
net_upgrade - 从指定的文件（在tftpserver中）进行更新
otp_printf- otp_printf - 打印otp值
ping - 向网络主机发送ICMP ECHO_REQUEST
readbbm -读取BBM表
readcis - 读取cis块内容
reset - 执行CPU的RE
riu - riu - riu 命令
run - 在环境变量中运行命令
saveenv - 将环境变量保存持久存储
sdstar - 通过 sd 包运行脚本
secauth - 控制 Sstar 安全认证序列
setenv - 设置环境变量sfbin - 用于将 sf 图像上传到服务器（通过网络使用 TFTP 协议）
show_hello- - 你好世界
srcfg- 传感器引脚和 mclk 配置。
usbstar - 通过 USB 包运行脚本
usbupdate- usbupdate - 通过 USB_DISK更新系统，不使用控制台
ustar - 通过 USB 运行脚本
version - 打印监视器、编译器和链接器的版本
writecis- dram 中搜索 CIS，然后写入 spinand。
xhprint - - 你好世界
xhprintenv- 打印环境
